Microphones in practice 10 min read
Sound and Microphones in Practice
Review sound and microphone fundamentals, then apply polar patterns, specifications, placement and array behavior to practical AV designs.
- Explain amplitude, frequency, wavelength and phase.
- Describe how dynamic, condenser and MEMS microphones work.
- Interpret common polar patterns.
- Read the microphone specifications that matter in commercial AV.
- Select and place microphones based on distance, room acoustics and loudspeaker location.
Why an AV engineer should care
A microphone does not know which sound is important. It receives changing air pressure from the talker, loudspeakers, HVAC, reflections, chair noise and the person attacking a bag of chips during the meeting.
Good microphone selection and placement therefore begin with three questions:
- How does sound travel?
- How does the microphone convert it into electricity?
- From which directions is the microphone most sensitive?
DSP can improve a usable signal. It cannot fully separate clean speech from room noise and reverberation after all of them have entered the same capsule.
1. What sound physically is
Sound in air is a longitudinal pressure wave. Something moves—a vocal cord, loudspeaker cone or dropped microphone—and alternately compresses and relaxes the nearby air. Those pressure variations travel outward.
The air itself does not race from the presenter to the microphone. Individual molecules move slightly around their resting positions while the pressure disturbance travels through them.
Four properties describe the wave:
Amplitude
Amplitude describes the size of the pressure variation. Greater amplitude generally means greater sound-pressure level, measured in dB SPL.
Amplitude is what we usually mean by “level,” although human loudness perception also depends on frequency and duration.
Frequency
Frequency is the number of complete cycles per second, measured in hertz.
- 100 Hz: low-frequency energy
- 1,000 Hz: midrange
- 10,000 Hz: high-frequency detail
Complex sounds contain many frequencies simultaneously. Speech includes a fundamental pitch plus harmonics and noise components. Much of speech intelligibility comes from the midrange and upper-midrange rather than the lowest vocal frequencies.
Wavelength
Wavelength is the physical length of one cycle:
λ = (c) / (f)
Where:
λ= wavelengthc= speed of soundf= frequency
At approximately 20°C, sound travels around 343 metres per second:
| Frequency | Approximate wavelength |
|---|---|
| 100 Hz | 3.43 m / 11.3 ft |
| 1 kHz | 34 cm / 13.5 in |
| 10 kHz | 3.4 cm / 1.35 in |
This helps explain why low frequencies bend around objects and pass through construction more readily, while high frequencies are more easily blocked, reflected and directed.
Phase
Phase describes where a wave is within its cycle relative to another wave.
Two identical signals arriving together reinforce each other. If one arrives later, some frequencies reinforce while others cancel. Multiple microphones capturing the same source at different distances can therefore produce comb filtering: a series of peaks and cancellations across the frequency response.
Phase matters in microphone arrays, loudspeaker alignment and DSP delay.
2. Direct sound, reflections and distance
A microphone receives several versions of the talker:
- Direct sound: travels straight from the mouth to the microphone.
- Early reflections: bounce once or twice from tables, walls or ceilings.
- Reverberant sound: arrives after many reflections from many directions.
- Noise: HVAC, projectors, fans, hallway sound and other occupants.
In a free field, doubling the distance from a point source reduces the direct sound by approximately 6 dB. (support.biamp.com) Real rooms differ because reflected sound does not fall at exactly the same rate.
This produces one of the most useful rules in audio:
Improving talker-to-microphone distance usually helps more than adding DSP.
Move a microphone from four feet away to one foot away and the direct speech can improve by roughly 12 dB relative to steady room noise. No compressor, AGC or “AI audio” button creates that same acoustic advantage cleanly.
3. A microphone is a transducer
A transducer converts energy from one form to another. A microphone converts acoustic pressure variations into a corresponding electrical signal.
Dynamic moving-coil microphone
A dynamic microphone contains:
- A diaphragm
- A coil attached to the diaphragm
- A permanent magnet
Sound moves the diaphragm and coil. The coil moves through the magnetic field and generates a small voltage.
Dynamic microphones are rugged, tolerate high SPL and require no phantom power for the capsule. Their moving assembly is comparatively massive, so they are commonly used close to talkers, instruments and other strong sources.
Condenser microphone
A condenser capsule contains:
- A thin conductive diaphragm
- A nearby backplate
- An electrical charge
Together, the diaphragm and backplate form a capacitor. Sound changes the spacing between them, changing capacitance and creating an electrical representation of the waveform.
The capsule and its internal electronics require power. In professional AV, that commonly comes from:
- 48 V phantom power
- An internal battery
- Network or USB power
- A permanently charged electret element with powered electronics
Condenser elements can be small, sensitive and responsive to fine detail, making them common in goosenecks, lavaliers, boundary microphones and ceiling arrays. Shure identifies dynamic and condenser as the two principal microphone operating types and describes the diaphragm/coil/magnet and charged diaphragm/backplate mechanisms. (shure.com, service.shure.com)
Ribbon microphone
A ribbon microphone suspends a very thin conductive ribbon inside a magnetic field. The ribbon serves as both diaphragm and electrical conductor.
Ribbon microphones are valued in recording, but they are uncommon in ordinary commercial AV because they can be delicate, have relatively low output and often present a natural figure-eight pattern.
MEMS microphone
A MEMS microphone creates a miniature diaphragm and sensing structure on a semiconductor. MEMS elements appear in laptops, conferencing appliances and multi-element microphone arrays.
A ceiling array may contain dozens of small elements. The manufacturer’s DSP combines them using timing and level differences to form steerable or trackable pickup beams.
4. Polar patterns: where the microphone listens
A polar pattern plots microphone sensitivity by direction. It does not show a hard-edged coverage bubble, and it does not guarantee that sound outside the pattern disappears.
Real patterns also change with frequency. Always inspect the manufacturer’s plots when placement matters.
| Pattern | Strongest pickup | Greatest rejection | Typical AV use |
|---|---|---|---|
| Omnidirectional | All directions | None | Lavalier, table or ambient pickup |
| Cardioid | Front | Rear | Lectern, handheld and table mic |
| Supercardioid | Narrower front plus small rear lobe | Roughly 125° off-axis | Presenter or performance mic |
| Hypercardioid | Narrow front with larger rear lobe | Roughly 110° off-axis | Focused pickup in controlled placement |
| Figure-eight | Front and rear | Sides | Specialty recording and some array elements |
A cardioid is not simply an omni with its rear turned off. Directional microphones compare pressure arriving at different parts of the capsule through acoustic ports. That pressure-gradient operation makes their response dependent on direction and frequency.
Aim the null, not merely the front
For feedback control, the microphone’s least-sensitive direction should face the troublesome loudspeaker:
- Cardioid: loudspeaker toward the rear.
- Supercardioid: loudspeaker near its off-axis nulls, because it has a small rear pickup lobe.
- Figure-eight: loudspeaker toward either side.
Putting a floor monitor directly behind a supercardioid microphone can place it in the rear lobe. The microphone is technically “pointed correctly” while the system still howls like it has been personally betrayed.
Proximity effect
Most directional microphones gain low-frequency response when positioned very close to the source. This is proximity effect.
It can add warmth to a handheld vocal, but it can also make a lectern or conferencing microphone sound boomy when the talker leans in. Omnidirectional pressure microphones generally do not exhibit proximity effect. (shure.com, shure.com)
5. Specifications that actually help
For commercial AV, examine:
- Frequency response: Sensitivity across frequency.
- Polar pattern: Directional response, preferably at several frequencies.
- Sensitivity: Electrical output for a stated acoustic level, commonly mV/Pa or dBV/Pa.
- Maximum SPL: Loudest input before specified distortion.
- Self-noise: Noise generated by an active microphone’s own electronics.
- Signal-to-noise ratio: Useful signal compared with noise.
- Output impedance: Electrical loading requirement.
- Power requirement: Phantom, battery, USB, PoE or proprietary power.
- Connector and output type: Analog, USB, Dante or another network transport.
Greater sensitivity does not mean “better microphone.” It means more electrical output for the same sound pressure. Placement, self-noise, polar response and room conditions still determine the result.
6. Practical example: lectern microphone
A lectern microphone must accommodate different heights and speaking positions while rejecting loudspeakers and room noise.
A practical design might use a cardioid or supercardioid condenser gooseneck:
- Keep the capsule reasonably close to the talker.
- Aim it toward the mouth rather than the chest.
- Position loudspeakers near the appropriate rejection angle.
- Use a shock mount to reduce lectern vibration.
- Provide a windscreen for breath and plosive control.
- Check the pattern before placing a confidence monitor behind it.
A longer gooseneck can improve talker distance for shorter users, but it may obstruct sightlines. That is an architectural and human-factors tradeoff, not merely an audio specification.
7. Practical example: ceiling microphone array
A Shure MXA or Biamp Parlé ceiling array combines multiple elements and DSP to steer or track beams. Biamp describes beamforming microphones as arrays whose pickup patterns can be aimed using DSP. (tesira-help.biamp.com)
The array improves directional selectivity, but it still obeys acoustics:
- A high ceiling increases talker distance.
- HVAC noise near the array reduces SNR.
- Hard rooms increase reflected speech.
- Loudspeakers still require an AEC reference.
- Coverage drawings must account for seating and room configuration.
- Automatic tracking does not turn a distant whisper into a close-miked studio recording.
For system documentation, show mounting height, intended talker zones, loudspeaker locations and the network/DSP channel path. “One ceiling mic covers room” is an equipment count, not a design.
Practical exercise
Use a microphone with a visible input meter:
- Speak at a fixed level from one foot away.
- Record the meter reading.
- Repeat at two and four feet.
- Return to the original distance and move around the microphone while maintaining the same radius.
- Compare the readings with its published polar pattern.
The distance changes should roughly demonstrate direct-sound loss. The walk-around test reveals the rear and side rejection—and usually proves that the polar plot is not a magical sound force field.
Compact glossary
- Amplitude: Magnitude of a pressure or electrical variation.
- Frequency: Cycles per second, measured in hertz.
- Wavelength: Physical length of one cycle.
- Phase: Relative position within a waveform cycle.
- Transducer: Device that converts one form of energy into another.
- Diaphragm: Thin moving membrane within a microphone.
- Polar pattern: Microphone sensitivity by direction.
- Proximity effect: Bass increase near most directional microphones.
- MEMS: Micro-electromechanical system.
- Comb filtering: Repeating frequency cancellations caused by delayed copies of a signal.
- SNR: Signal-to-noise ratio.
Review questions
- Why does reducing talker-to-microphone distance improve intelligibility?
- How does a moving-coil dynamic microphone generate voltage?
- Why can placing a loudspeaker directly behind a supercardioid microphone be a problem?
Answers
-
Direct speech becomes stronger relative to room noise and reverberation.
-
Sound moves a diaphragm and attached coil through a magnetic field, generating a corresponding electrical signal.
-
A supercardioid has a small rear pickup lobe. Its strongest rejection occurs off-axis rather than directly behind it.
Discuss a project